In North Texas the AC runs most of the year, and in many homes the air handler and ducts sit in a hot attic. That combination of cold surfaces, humid air and dust is a common recipe for moisture problems.
Why AC systems collect moisture
An air conditioner cools air by pulling heat and moisture out of it. The moisture lands on a cold coil and is supposed to drip into a pan and leave the house through a condensate line. When any part of that path fails, the water goes somewhere it should not. NWS normals for DFW show July and August highs near 96 degrees, with around 20 days a year at 100 or above, so the system works hard and makes a lot of water.
Brick-veneer homes on slab foundations, which are common across Fort Worth, Arlington and Dallas, often put the air handler in the attic because there is no basement and little floor space. That puts a cold, wet piece of equipment in the hottest, dustiest part of the house. Ducts in the same attic can sweat when cold air runs through them in hot, humid air. All of it is normal wear on a system, not a sign you did something wrong.
The usual causes
- A clogged condensate drain line. Algae and sludge plug the line, and the pan overflows. In an attic this can soak insulation and drywall for a long time before a ceiling stain appears.
- A rusted or cracked drain pan. Older pans fail, and a failed pan leaks quietly.
- Sweating ducts. Torn or missing duct insulation lets cold ducts meet hot, humid attic air.
- An oversized unit. A system that cools too fast shuts off before it has removed much moisture, so indoor air stays damp.
- Leaky return ducts. A return that pulls in attic air brings humidity and dust into the system.
- Dirty coils and filters. Dust holds moisture and feeds growth.
Signs to look for
A musty smell when the AC starts is the most common sign. Others include water stains on the ceiling below an attic unit, dark spotting around supply vents or on the vent louvers, visible growth on the drain pan or on duct insulation, and rooms that feel clammy even though the thermostat is satisfied. Spotting on a vent is often dust, so do not assume it is mold. If you are unsure, our guide to a musty smell without visible mold covers the places to check, and black mold facts explains why a dark color alone proves nothing.
If you see water around the unit, treat it as a leak first. Switch the system off at the thermostat and, if you can reach the shutoff safely, at the air handler, and get the drain cleared. Running a system that is actively dripping into insulation makes the problem larger.
What stays inside the system and what spreads
EPA says it is important to dry water-damaged areas and items within 24 to 48 hours to prevent mold growth, and a chronic AC leak is simply water damage that keeps happening. The concern with a ducted system is that it moves air through the entire house, so a problem at the coil or in a duct can reach many rooms. That is why a stain near a vent is worth looking at early, before it grows. EPA also suggests keeping indoor humidity below 60 percent, ideally between 30 and 50 percent. If your house stays above that with the AC running, something in the system or the house needs attention.
Who handles what
This is where homeowners often get confused. An HVAC technician repairs the equipment: the drain line, the pan, the coil, the duct insulation. A mold company deals with the mold itself and the materials it grew on. Often you need both. Fixing the leak without cleaning up the growth leaves the contamination in place, and cleaning mold without fixing the leak means it comes back.
On our site, the service page for AC and duct mold removal in Fort Worth describes what a mold company does with an HVAC system, and attic mold removal covers the surrounding space when insulation or decking is affected. If the question is whether you have a problem at all, a mold inspection checks moisture readings and looks at the system and the attic together.
Cleaning ducts is not the same as mold remediation
A routine duct cleaning removes dust and debris. It is not designed to address mold growth from a water problem, and it does not fix the cause. In Texas, if mold is found, the work falls under TDLR's mold rules. TDLR states a person must hold a mold remediation or mold assessment license to provide those services, with an exemption for visible mold under 25 contiguous square feet and for owner work. Inside a duct system, the contiguous area can be hard to measure, so ask the assessor or contractor how they treated the limit.
On larger jobs TDLR says an assessment consultant prepares a mold remediation protocol specific to the project, and a remediation contractor creates a work plan that follows it, with both reaching the client at least one calendar day before work begins. TDLR also says the same person generally cannot do both the assessment and the remediation on the same project. Details are in the Texas mold license rules guide, and the steps are laid out in what happens during mold remediation.
What to avoid
- Do not spray bleach or disinfectant into ducts or onto a coil. EPA says biocides such as chlorine bleach are not recommended as a routine practice during mold cleanup, and warns never to mix bleach with ammonia-containing cleaners.
- Do not run the system while a pan is overflowing.
- Do not assume a sample is needed. EPA says that in most cases, if visible mold growth is present, sampling is unnecessary. If you want to know what testing does and does not tell you, read mold inspection versus mold testing.
- Do not climb into a hot attic for long. Summer attic temperatures are punishing, so leave the inspection to someone prepared for it or go early in the morning.
What it can cost
These are national published figures, not quotes. A cost guide puts HVAC or duct mold work at $2,000 to $10,000 per job, depending on the system type and how far growth has spread. For the attic around it, the same source gives $1,500 to $6,000 for a partial attic and $6,000 to $15,000 for a full one, higher with extensive damage or insulation replacement. Repairing the drain line or pan is a separate HVAC cost and is usually far smaller. For Fort Worth numbers, see the mold remediation cost guide.
Questions to ask before work starts
Ask who is fixing the water source and who is handling the growth, and how the two visits will be coordinated. Ask whether the attic insulation around the unit will be assessed, since wet insulation holds moisture long after the leak stops. Ask how the contractor will contain the work area so that disturbed material does not travel through the house, and whether the system will stay off during the work. Ask for the written protocol and work plan, and confirm the license numbers in TDLR's search before signing. If a company will not explain its plan in plain terms, keep looking.
Also think about timing. Many homeowners find an AC problem in July, when every HVAC company is busy and the house is hot. A cracked pan or a plugged line found in the cooler months gives you time to compare options and to dry the area properly, so a spring check before the heat arrives is worth the small cost.
Preventing a repeat
- Have the condensate line and pan checked at your regular tune-up, before the summer peak.
- Replace filters on schedule.
- Look at duct insulation when you are in the attic and note any gaps or wet spots.
- Keep an eye on humidity, aiming for the 30 to 50 percent range EPA mentions.
- Check the ceiling under an attic unit after a hard-running week.
Next step
Tell them where the unit sits, what you have seen and smelled, and whether a leak has been repaired. That gets you to the right first visit. Towns with many slab-on-grade homes, such as Grand Prairie and AC and duct mold work in Mansfield, are covered the same way as Fort Worth.
Frequently asked questions
Why does my AC smell musty when it turns on?
Can an attic air handler leak without me noticing?
Does duct cleaning remove mold?
Do I need a TDLR license holder for a small amount of mold on a vent?
Sources
Last updated: